What to do if the car tire light is on?

At times while driving your car, you must have noticed your car tire light getting switched on. Well, the tire light has a single purpose: to alert the driver in case of flat tires. So, when you find the tire light on, you must have a tire with under-inflation. Your cars and vehicles have a safety feature called the tire pressure monitoring system. It is wise to ensure that drivers always have the safety feature activated so that it is operational. 

If you notice any inconsistency that you do not understand you can initiate a search like a mechanic shop near me in Houston if you are a resident of Texas.

Why is it important to activate the tire light feature?

The tire pressure monitoring system or TPMS is quite an important component in your car’s safety system. It might not be very salient to you but you must never ignore them. If your car tires are severely underinflated then it can be because of the following reasons- 

  • Decrease the fuel economy
  • Reduction in the lifespan of car tires due to irregular wear and tear
  • Affect the safety of the driver on the streets because of underinflated car tires 
  • Unpredictable handling of the vehicle
  • Due to the increase in road force

If you have an inflated tire, probably the first option would be to visit a car repair shop.

When the tire light turns on what should be done?

When your car’s safety system turns on the TPMS while you are driving, you might want to pull over. It would be better if you could drive over to a gas station. If that is not possible, try looking for any rest stop with an air pump. Once you are there you must immediately inflate your car tires to the standard PSI. Car tires often lose their pressure balance due to two factors- 

  • Any sudden reduction in the temperature
  • Any small puncture or leakage in the tires 

If you want to change the settings of the tire pressure light, you will likely be experiencing a fall in temperature. When there is a sudden reduction in temperature, the air inside gets dense inside. It takes up less space and hence reduces the pressure in the tires. However, the tpms light is often turned on when the driver recognizes he requires a tire replacement. A leak or puncture would likely result in a flat tire. In this situation, you might want to get a free tire inspection or pay a visit to a car mechanic. 

What if the car tpms light remains activated even after topping it to the recommended PSI? 

The tire light might be still on even after the driver topped off the car tires to the standard PSI. In ideal conditions, the driver should be able to hit the streets again. However, if the tpms light is still burning yellow, there must be some other reasons apart from leakages. 

If this is the case, then your need to do the following-

Given that the tire pressure light is on even after doing the due work required, you need to change its initial default settings. This could be possible even if there is adequate air in the tires. Therefore, you must go through the following steps for resetting the tire light. However, you can do an aircheck before proceeding.

  • Please keep in mind that only administer the following steps if that light remains on even after inflating the car tires with proper pressure- 
  • You can drive the car at 50 mph for approximately 10 minutes- This haul could reset the changes in the sensor. And for the next time you restart the vehicle, the tpms light is likely to be turned off. 
  • You can try turning the ignition position “On” without actually starting the car. Then, you need to press on the tpms reset switch and press it until the light begins to blink three times. After it is done, you can release the button. 
  • Try starting the car again and keep the ignition on for about 20 minutes. This will help in resetting the sensor. You might likely find the tire pressure monitor reset switch right beneath the car’s steering wheel. However, you must check your user manual if you have difficulty locating the button. 
  • There are a few alternate ways of resetting the TPMS light that is somewhat more inclusive and tedious. If these seem beyond what you can deal with, simply bring your vehicle to a mechanic shop in Houston to deal with the issues.
  • You can inflate each tire to 3 PSI over the suggested sum, then, at that point, collapse them. Your extra tire may likewise have a sensor so try to incorporate it also. After every tire has been collapsed, reinflate them to the appropriate PSI.
  • Open the hood and disengage the positive battery link with the vehicle off. Turn the way into the “On” position and sound the horn for around three seconds to release any power actually put away in the vehicle. Then, at that point, reconnect the battery.

Given that even after following the above steps, if you fail to reset the sensor then you must visit an auto repair in Houston.

What does it mean when you have a continuous flashing tire pressure light?

Your TPMS light might be flickering when you start your vehicle. You can just switch it off for a couple of moments later, this is quite typical. Most of the cars flash their warning signals. Assuming the light keeps on flickering or starts blazing while you’re driving, there could be an issue.

A flickering tire pressure light could establish that there is an issue with the sensors or the sensor battery.

To Wrap Up

J&T Automotive is very helpful in maintenance and repair services. The quality of the services provided by the company is very remarkable as per our clients. We employ our fine team of technicians in their respective areas of expertise. The aim is to offer satisfying service to all our clients. 

713-464-2312
Scroll to Top